You are not logged in.

#1 2020-12-05 07:39:19

Nili
Member
From: $HOME/♫♪
Registered: 2015-09-30
Posts: 988
Website

Can i trust or use this HDD again?

Hello! I need an opinion or interpretation. I have one external HDD with some error signs, but I'm not sure in what condition her degradation is.

I have made a check on Windows that have collected a different results.
Also have made check with gsmartcontrol gui via Linux that are shown on images or text outputs

>>> 1rst check before doing Windows disk checkup
50681679256_406d41f9ca_n.jpg

smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.9.0-4-amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F2 EG
Device Model:     SAMSUNG HD154UI
Serial Number:    S1Y6J9BZA00578
LU WWN Device Id: 5 0024e9 203862558
Firmware Version: 1AG01118
User Capacity:    1,500,301,910,016 bytes [1.50 TB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Wed Dec  2 12:49:09 2020 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(19356) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 323) minutes.
Conveyance self-test routine
recommended polling time: 	 (  34) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   100   051    -    59
  3 Spin_Up_Time            POS---   071   071   011    -    9480
  4 Start_Stop_Count        -O--CK   099   099   000    -    856
  5 Reallocated_Sector_Ct   PO--CK   100   100   010    -    0
  7 Seek_Error_Rate         POSR--   100   100   051    -    0
  8 Seek_Time_Performance   P-S--K   100   100   015    -    10863
  9 Power_On_Hours          -O--CK   094   094   000    -    31964
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count -O--C-   100   100   000    -    0
 12 Power_Cycle_Count       -O--CK   099   099   000    -    734
 13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    59
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   100   100   000    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    85
188 Command_Timeout         -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   094   064   000    -    6 (Min/Max 6/6)
194 Temperature_Celsius     -O---K   094   066   000    -    6 (Min/Max 6/6)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    73468
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O--C-   100   100   000    -    12
198 Offline_Uncorrectable   ----CK   100   100   000    -    1
199 UDMA_CRC_Error_Count    -OSRCK   100   100   000    -    0
200 Multi_Zone_Error_Rate   -O-R--   100   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   253   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x04       GPL     R/O      2  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x20       GPL     R/O      2  Streaming performance log [OBS-8]
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 38 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 38 [5] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 78 57 47 00  Error: UNC at LBA = 0x573f7857 = 1463777367

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 78 57 47 00     00:05:07.020  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 4f 47 00     00:05:06.980  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 47 47 00     00:05:06.700  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 3f 47 00     00:05:06.500  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 37 47 00     00:05:06.500  READ DMA EXT

Error 37 [4] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 6a 16 47 00  Error: UNC at LBA = 0x573f6a16 = 1463773718

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 6a 0f 47 00     00:04:35.440  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 6a 07 47 00     00:04:35.260  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 ff 47 00     00:04:35.240  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 f7 47 00     00:04:35.140  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 ef 47 00     00:04:35.140  READ DMA EXT

Error 36 [3] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 a7 47 00  Error: UNC at LBA = 0x573f69a7 = 1463773607

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 a7 47 00     00:04:24.830  READ DMA EXT

Error 35 [2] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 a7 47 00  Error: UNC at LBA = 0x573f69a7 = 1463773607

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 a7 47 00     00:04:02.400  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 9f 47 00     00:04:02.180  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 97 47 00     00:04:01.690  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 8f 47 00     00:04:01.670  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 87 47 00     00:04:01.350  READ DMA EXT

Error 34 [1] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 85 47 00  Error: UNC at LBA = 0x573f6985 = 1463773573

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 7f 47 00     00:03:53.430  READ DMA EXT

Error 33 [0] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 85 47 00  Error: UNC at LBA = 0x573f6985 = 1463773573

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 7f 47 00     00:03:48.880  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 77 47 00     00:03:48.870  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 6f 47 00     00:03:48.560  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 67 47 00     00:03:48.360  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 5f 47 00     00:03:48.360  READ DMA EXT

Error 32 [7] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 59 a5 47 00  Error: UNC at LBA = 0x573f59a5 = 1463769509

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 59 9f 47 00     00:03:03.230  READ DMA EXT

Error 31 [6] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 59 a5 47 00  Error: UNC at LBA = 0x573f59a5 = 1463769509

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 59 9f 47 00     00:02:52.240  READ DMA EXT

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       20%     31962         1463769485

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                     6 Celsius
Power Cycle Min/Max Temperature:     --/ 6 Celsius
Lifetime    Min/Max Temperature:     --/44 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (62)

Index    Estimated Time   Temperature Celsius
  63    2020-12-02 10:42    16  -
  64    2020-12-02 10:43    17  -
 ...    ..(  6 skipped).    ..  -
  71    2020-12-02 10:50    17  -
  72    2020-12-02 10:51    18  -
 ...    ..(  3 skipped).    ..  -
  76    2020-12-02 10:55    18  -
  77    2020-12-02 10:56    19  -
  78    2020-12-02 10:57    19  -
  79    2020-12-02 10:58    19  -
  80    2020-12-02 10:59    20  *
 ...    ..(  2 skipped).    ..  *
  83    2020-12-02 11:02    20  *
  84    2020-12-02 11:03    21  **
 ...    ..(  3 skipped).    ..  **
  88    2020-12-02 11:07    21  **
  89    2020-12-02 11:08    22  ***
  90    2020-12-02 11:09    22  ***
  91    2020-12-02 11:10    24  *****
 ...    ..( 13 skipped).    ..  *****
 105    2020-12-02 11:24    24  *****
 106    2020-12-02 11:25    25  ******
 ...    ..( 31 skipped).    ..  ******
  10    2020-12-02 11:57    25  ******
  11    2020-12-02 11:58    26  *******
 ...    ..( 16 skipped).    ..  *******
  28    2020-12-02 12:15    26  *******
  29    2020-12-02 12:16    27  ********
  30    2020-12-02 12:17    26  *******
  31    2020-12-02 12:18    27  ********
 ...    ..( 28 skipped).    ..  ********
  60    2020-12-02 12:47    27  ********
  61    2020-12-02 12:48     6  -
  62    2020-12-02 12:49     6  -

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error medium or hardware error (serious)
Read Device Statistics page 0x00 failed

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            0  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC

>>> 2nd check after Windows disk checkup
☑ Automatically fix file system errors
☑ Scan for and attempt recovery of bad sectors

50681680181_fa4a9c9904_n.jpg

smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.9.0-4-amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F2 EG
Device Model:     SAMSUNG HD154UI
Serial Number:    S1Y6J9BZA00578
LU WWN Device Id: 5 0024e9 203862558
Firmware Version: 1AG01118
User Capacity:    1,500,301,910,016 bytes [1.50 TB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Sat Dec  5 07:39:44 2020 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(19356) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 323) minutes.
Conveyance self-test routine
recommended polling time: 	 (  34) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   100   051    -    15
  3 Spin_Up_Time            POS---   072   072   011    -    9150
  4 Start_Stop_Count        -O--CK   099   099   000    -    864
  5 Reallocated_Sector_Ct   PO--CK   100   100   010    -    0
  7 Seek_Error_Rate         POSR--   100   100   051    -    0
  8 Seek_Time_Performance   P-S--K   100   100   015    -    10448
  9 Power_On_Hours          -O--CK   094   094   000    -    32030
 10 Spin_Retry_Count        PO--CK   100   100   051    -    0
 11 Calibration_Retry_Count -O--C-   100   100   000    -    0
 12 Power_Cycle_Count       -O--CK   099   099   000    -    739
 13 Read_Soft_Error_Rate    -OSR--   100   100   000    -    15
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   100   100   000    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    88
188 Command_Timeout         -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   075   064   000    -    25 (Min/Max 24/30)
194 Temperature_Celsius     -O---K   074   066   000    -    26 (Min/Max 24/31)
195 Hardware_ECC_Recovered  -O-RC-   100   100   000    -    87212
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   100   100   000    -    0
200 Multi_Zone_Error_Rate   -O-R--   100   100   000    -    0
201 Soft_Read_Error_Rate    -O-R--   100   100   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      2  Ext. Comprehensive SMART error log
0x04       GPL     R/O      2  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x20       GPL     R/O      2  Streaming performance log [OBS-8]
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 39 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 39 [6] occurred at disk power-on lifetime: 31985 hours (1332 days + 17 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 59 a5 47 00  Error: UNC at LBA = 0x573f59a5 = 1463769509

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 d0 00 80 00 00 57 3f 59 5f 47 00     02:41:36.690  READ DMA EXT
  25 00 d0 00 80 00 00 57 3f 58 df 47 00     02:41:36.350  READ DMA EXT
  25 00 d0 00 80 00 00 57 3f 58 5f 47 00     02:41:35.900  READ DMA EXT
  25 00 d0 00 80 00 00 57 3f 57 df 47 00     02:41:34.740  READ DMA EXT
  25 00 d0 00 80 00 00 57 3f 57 5f 47 00     02:41:34.500  READ DMA EXT

Error 38 [5] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 78 57 47 00  Error: UNC at LBA = 0x573f7857 = 1463777367

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 78 57 47 00     00:05:07.020  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 4f 47 00     00:05:06.980  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 47 47 00     00:05:06.700  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 3f 47 00     00:05:06.500  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 78 37 47 00     00:05:06.500  READ DMA EXT

Error 37 [4] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 6a 16 47 00  Error: UNC at LBA = 0x573f6a16 = 1463773718

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 6a 0f 47 00     00:04:35.440  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 6a 07 47 00     00:04:35.260  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 ff 47 00     00:04:35.240  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 f7 47 00     00:04:35.140  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 ef 47 00     00:04:35.140  READ DMA EXT

Error 36 [3] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 a7 47 00  Error: UNC at LBA = 0x573f69a7 = 1463773607

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 a7 47 00     00:04:24.830  READ DMA EXT

Error 35 [2] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 a7 47 00  Error: UNC at LBA = 0x573f69a7 = 1463773607

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 a7 47 00     00:04:02.400  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 9f 47 00     00:04:02.180  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 97 47 00     00:04:01.690  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 8f 47 00     00:04:01.670  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 87 47 00     00:04:01.350  READ DMA EXT

Error 34 [1] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 85 47 00  Error: UNC at LBA = 0x573f6985 = 1463773573

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 7f 47 00     00:03:53.430  READ DMA EXT

Error 33 [0] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 69 85 47 00  Error: UNC at LBA = 0x573f6985 = 1463773573

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 69 7f 47 00     00:03:48.880  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 77 47 00     00:03:48.870  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 6f 47 00     00:03:48.560  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 67 47 00     00:03:48.360  READ DMA EXT
  25 03 03 00 08 00 00 57 3f 69 5f 47 00     00:03:48.360  READ DMA EXT

Error 32 [7] occurred at disk power-on lifetime: 31905 hours (1329 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 57 3f 59 a5 47 00  Error: UNC at LBA = 0x573f59a5 = 1463769509

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 03 03 00 08 00 00 57 3f 59 9f 47 00     00:03:03.230  READ DMA EXT

SMART Extended Self-test Log Version: 1 (2 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Conveyance offline  Completed without error       00%     32030         -
# 2  Extended offline    Completed without error       00%     32022         -
# 3  Short offline       Completed without error       00%     32016         -
# 4  Short offline       Completed: read failure       20%     31983         1463769509
# 5  Short offline       Completed: read failure       20%     31962         1463769485
2 of 2 failed self-tests are outdated by newer successful extended offline self-test # 2

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    26 Celsius
Power Cycle Min/Max Temperature:     --/31 Celsius
Lifetime    Min/Max Temperature:     --/44 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -4/72 Celsius
Min/Max Temperature Limit:           -9/77 Celsius
Temperature History Size (Index):    128 (125)

Index    Estimated Time   Temperature Celsius
 126    2020-12-05 05:32    25  ******
 ...    ..( 11 skipped).    ..  ******
  10    2020-12-05 05:44    25  ******
  11    2020-12-05 05:45    24  *****
  12    2020-12-05 05:46    25  ******
  13    2020-12-05 05:47    24  *****
 ...    ..(  2 skipped).    ..  *****
  16    2020-12-05 05:50    24  *****
  17    2020-12-05 05:51    25  ******
 ...    ..( 16 skipped).    ..  ******
  34    2020-12-05 06:08    25  ******
  35    2020-12-05 06:09    24  *****
  36    2020-12-05 06:10    24  *****
  37    2020-12-05 06:11    25  ******
  38    2020-12-05 06:12    25  ******
  39    2020-12-05 06:13    24  *****
  40    2020-12-05 06:14    25  ******
 ...    ..(  9 skipped).    ..  ******
  50    2020-12-05 06:24    25  ******
  51    2020-12-05 06:25    26  *******
 ...    ..(  4 skipped).    ..  *******
  56    2020-12-05 06:30    26  *******
  57    2020-12-05 06:31    27  ********
 ...    ..( 11 skipped).    ..  ********
  69    2020-12-05 06:43    27  ********
  70    2020-12-05 06:44    28  *********
 ...    ..( 30 skipped).    ..  *********
 101    2020-12-05 07:15    28  *********
 102    2020-12-05 07:16    27  ********
 ...    ..( 14 skipped).    ..  ********
 117    2020-12-05 07:31    27  ********
 118    2020-12-05 07:32    26  *******
 ...    ..(  6 skipped).    ..  *******
 125    2020-12-05 07:39    26  *******

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error medium or hardware error (serious)
Read Device Statistics page 0x00 failed

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            0  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC

I have copied all the files successfully without problem, I formatted it in the fast and long option. Can i still use this hdd or throw it away?

Thank you for any advice.


OS: Devuan GNU/Linux 4 (chimaera/ceres)
WM: CWM

Studio Ghibli

Offline

#2 2020-12-05 12:25:45

twoion
ほやほや
Registered: 2015-08-10
Posts: 3,069

Re: Can i trust or use this HDD again?

It is normal for a disk to have a few bad sectors. Mechanics. For this, the disk has reserve sectors which seem to be already be used by this one. Attributes are also sometimes heavily vendor specific; the raw value may not mean much. I would put repeated heavy load on the disk (write zeroes over entire disk, multiple times, write random, whatever) and monitor the values. Should they stabilize -- sometimes seek counters just count seeks so be aware that they may spin or even overflow -- I'd use the disk for secondary or nonimportant data, such as movies.


Per aspera ad astra.

Offline

#3 2020-12-06 13:44:11

Nili
Member
From: $HOME/♫♪
Registered: 2015-09-30
Posts: 988
Website

Re: Can i trust or use this HDD again?

Thank you twoion for valid suggestions, I have already started doing some tests to see the progress of the numbers.
I will do so making this hdd as a secondary.

Best regards!


OS: Devuan GNU/Linux 4 (chimaera/ceres)
WM: CWM

Studio Ghibli

Offline

#4 2020-12-06 20:34:21

DeepDayze
Like sands through an hourglass...
From: In Linux Land
Registered: 2017-05-28
Posts: 1,073

Re: Can i trust or use this HDD again?

I concur with the other posters, just make that as a scratch drive for unimportant stuff or temp backups. Why  not put it into an external case to use it as a USB backup drive?


Real Men Use Linux

Offline

#5 2020-12-07 13:26:31

Nili
Member
From: $HOME/♫♪
Registered: 2015-09-30
Posts: 988
Website

Re: Can i trust or use this HDD again?

I did zeroes yesterday which lasted almost 2 days. In the end CrystalDiskInfo on Windows removed all negative info who reported early.

Meantime, gsmartcontrol reports back the same like 2nd pic "15 soft read error rate".
I will keep it under surveillance by doing further proofs like copy, paste, delete, place, play under this disk.

@DeepDayze it's with case already as an external disk.

Appreciate your inputs dear friends.


OS: Devuan GNU/Linux 4 (chimaera/ceres)
WM: CWM

Studio Ghibli

Offline

#6 2020-12-07 23:06:40

twoion
ほやほや
Registered: 2015-08-10
Posts: 3,069

Re: Can i trust or use this HDD again?

Nili wrote:

I did zeroes yesterday which lasted almost 2 days. In the end CrystalDiskInfo on Windows removed all negative info who reported early.

Meantime, gsmartcontrol reports back the same like 2nd pic "15 soft read error rate".
I will keep it under surveillance by doing further proofs like copy, paste, delete, place, play under this disk.

@DeepDayze it's with case already as an external disk.

Appreciate your inputs dear friends.

Well at some point you have to reach a conclusion as to what to do smile 2 days non-stop burnin and stable health would be good enough for me, personally.


Per aspera ad astra.

Offline

Board footer

Powered by FluxBB