Beryllium installer bug

0-day · 2022-12-23 13:08:49

I tried the beryllium, in live it works, when I go to install it hangs in system installation, is there any bug in the installer? thank you

Last edited by 0-day (2022-12-23 14:19:08)

rbh · 2022-12-23 13:44:44

0-day wrote:

when I go to install it hangs in system installation, is there any bug in the installer?

One known bug is that the installer hangs when configuring the network, if you have ill configured router.
A workaround is to disable ipv6 att boot with the kernel boot parameter "ipv6.disable=1".
Some graphic cards, needs boot parameter "nomodeset", but that should not be the case for you as you could boot the live session.

Have you tried to boot and start install plain Debian 11?
Are you choosing graphical installer? Have you tried to change to tty 4 and se if there is any errors?
Exactly where does the installer hangs?

Last edited by rbh (2022-12-23 14:05:14)

0-day · 2022-12-23 13:49:47

Sì blocca esattamente in installazione sistema

rbh · 2022-12-23 17:27:39

0-day wrote:

Sì blocca esattamente in installazione sistema

The forum language is English. You wrote: "Yes it crashes exactly in system install".

So, you can set language and keyboard layout, identifie the CD, Configure the network, set computername, create user and set password, partition disk and create mountpoints?

Does the installer crash, when installing the base system (Menu choise "Install system")?
Does installer start copying data to disk?
Does the installer hangs, nothing changes or do you get any message on the screen?
Is it the same if you are using text or graphical installer?
Is it the same if you are using the BL iso or Debian 11 iso?

Which arch are you installing? amd64 or i386
Can you turn to tty 4 to read messages there?

0-day · 2022-12-23 17:42:52

amd64
yes i can do all these things but when it gets to install the system just hangs and says the install has stalled.

rbh · 2022-12-23 18:01:19

0-day wrote:

amd64
yes i can do all these things but when it gets to install the system just hangs and says the install has stalled.

Once again:
Does installer start copying data to disk?
Does the installer hangs, nothing changes or do you get any message on the screen?
Is it the same if you are using text or graphical installer?
Is it the same if you are using the BL iso or Debian 11 iso?
Can you turn to tty 4 to read messages there?

And have you tested health of the harddrive?

0-day · 2022-12-23 18:11:03

the hard disk is good, graphical or text installation does not change anything, I already tried and install up to a certain point, then it hangs on system installation.Could it be the ISO is corrupted?

Last edited by 0-day (2022-12-23 18:12:19)

rbh · 2022-12-23 18:47:01

0-day wrote:

Could it be the ISO is corrupted?

You haven't verified the download? Follow instructions on the heompage:
https://www.bunsenlabs.org/installation … r-download.

If the iso is ok, check if you get the same result with Pure Debian install.

hhh · 2022-12-24 05:35:08

BTW, if you download via torrent, you don't need to run a checksum (and the download will resume if your Internet connection drops). Torrent has it's own file verification built-in.

0-day · 2022-12-24 09:36:43

the file was corrupted even when downloaded with torrent

#1 2022-12-23 13:08:49

Beryllium installer bug

#2 2022-12-23 13:44:44

Re: Beryllium installer bug

#3 2022-12-23 13:49:47

Re: Beryllium installer bug

#4 2022-12-23 17:27:39

Re: Beryllium installer bug

#5 2022-12-23 17:42:52

Re: Beryllium installer bug

#6 2022-12-23 18:01:19

Re: Beryllium installer bug

#7 2022-12-23 18:11:03

Re: Beryllium installer bug

#8 2022-12-23 18:47:01

Re: Beryllium installer bug

#9 2022-12-24 05:35:08

Re: Beryllium installer bug

#10 2022-12-24 09:36:43

Re: Beryllium installer bug

Board footer