You are not logged in.

#1 2021-05-25 10:41:21

Entrambosmares
New Member
Registered: 2021-05-25
Posts: 3

[SOLVED] Plank autostart

Hi!

I searched this: Link 2018 but isnt equal in this moment: fvR4r71
https://ibb.co/fvR4r71

¿How I do plank autostart in Lithium?

Thanks,

Last edited by hhh (2021-05-27 21:47:26)

Offline

#2 2021-05-25 11:28:13

damo
....moderator....
Registered: 2015-08-20
Posts: 6,619

Re: [SOLVED] Plank autostart

Bunsenlabs Lithium uses ~/.config/bunsen/autostart for the default session. That is the one you need to edit, unless your application is using XDG to autostart.

## BunsenLabs autostart
## ====================
## When you login to your BunsenLabs session, this autostart script
## will be executed to launch any applications
## you want to run at startup.
##
## NB, like openbox's autostart script, this uses the default shell,
## so "bashisms" are not supported.
##
## (Environment variables are set in ~/.config/bunsen/environment.)
##
## Note: some programs, such as 'nm-applet' are run via XDG autostart,
## from .desktop files in /etc/xdg/autostart and ~/.config/autostart.
## To disable this, comment out the last line in this file:
## "bl-xdg-autostart"
##
## Run 'bl-xdg-autostart --list' to list any XDG autostarted programs.
##

Have a look at Getting Started > Introduction to the Bunsenlabs Lithium Desktop


Be Excellent to Each Other...
The Bunsenlabs Lithium Desktop » Here
FORUM RULES and posting guidelines «» Help page for forum post formatting
Artwork on DeviantArt  «» BunsenLabs on DeviantArt

Offline

#3 2021-05-26 07:27:32

Entrambosmares
New Member
Registered: 2021-05-25
Posts: 3

Re: [SOLVED] Plank autostart

I already read that but I did not understand what I have to do, sorry.

Offline

#4 2021-05-26 10:19:00

damo
....moderator....
Registered: 2015-08-20
Posts: 6,619

Re: [SOLVED] Plank autostart

What is the command you need to start Plank? Add that to ~/.config/bunsen/autostart and then log out/in, or openbox --reconfigure

Read the autostart file and see how other commands have been used, Preferences > Bunsenlabs > Edit autostart


Be Excellent to Each Other...
The Bunsenlabs Lithium Desktop » Here
FORUM RULES and posting guidelines «» Help page for forum post formatting
Artwork on DeviantArt  «» BunsenLabs on DeviantArt

Offline

#5 2021-05-27 01:09:27

hhh
Meep!
Registered: 2015-09-17
Posts: 11,816
Website

Re: [SOLVED] Plank autostart

Entrambosmares wrote:

I already read that but I did not understand what I have to do, sorry.

Open your file manager (keyboard shortcut Ctrl+f). Show hidden folders and files (Ctrl+h). Navigate to /.config/bunsen and open the autostart file. Scroll down to where tint2, compton and conky are being started and after those entries (or anywhere near or the end of the file, make it the last line is fine too) add a new line...

plank &

Save the file! Log out, done. It should start when you log back in. Post back if it doesn't!

Offline

#6 2021-05-27 08:20:48

Entrambosmares
New Member
Registered: 2021-05-25
Posts: 3

Re: [SOLVED] Plank autostart

It is much easier than I was thinking. You just had to open Preferences> Bunsenlabs> Edit Autostart and typing at last plank &

I don't understand it. : `)

Thanks!

Last edited by Entrambosmares (2021-05-27 09:08:30)

Offline

#7 2021-05-27 21:46:40

hhh
Meep!
Registered: 2015-09-17
Posts: 11,816
Website

Re: [SOLVED] Plank autostart

Marking the thread [SOLVED].

Offline

Board footer

Powered by FluxBB